Description
Review this item in the context of the repair, installation access, nearby parts, and the result the completed job is intended to achieve.
Brand: GCD
| Operation Mode |
manual |
| Current Rating |
10 Amps |
| Operating Voltage |
12 Volts |
| Contact Type |
Normally Open |
| Connector Type |
Wire Leads |
| Brand |
GCD |
| Terminal |
Quick-connect |
| Circuit Type |
1-way |
| Mounting Type |
Panel Mount |
| Actuator Type |
Rocker |
| Contact Material |
Copper |
| Number of Positions |
1 |
| Control Method |
Touch |
| Connectivity Protocol |
X-10 |
| Color |
Roof Lights |
| Wattage |
1.2E+2 |
| Unit Count |
1.0 Count |
| Number of Items |
1 |
| Manufacturer |
GCD |
| Item Weight |
1.5 ounces |
| Package Dimensions |
8 x 5 x 2 inches |
| Manufacturer Part Number |
GCD-0106-S |
| Voltage |
12 Volts (DC) |
Fits All Jeep TJ / LJ Wranglers 1997-2006 This accessory rocker switch is made to fit the Jeep TJ Wranglers . This Switch is rated at 12 volts 10 amps. Simply snaps into your existing dash panel. It is custom made for running aftermarket accessories such as off-road lights, rock lights, back-ups, air compressors, Lockers etc. Be sure to always use a relay to power your accessories,
Vehicle information
Available fitment details
Listing compatibility notes
- 5 ounces Package Dimensions 8 x 5 x 2 inches Manufacturer Part Number GCD-0106-S Voltage 12 Volts (DC) Fits All Jeep TJ / LJ Wranglers 1997-2006 This accessory rocker switch is made to fit the Jeep TJ Wranglers .
Fitment data is provided as a buying aid. Verify the listing against your vehicle and existing part before ordering.
Repair scenarios, installation, companion parts, and use outcomes
Buying guidance
Quick decision
Review this interior light in the context of the repair and the surrounding components.
Repair scenario
- Identify the symptom and confirm that this is the component required by the repair.
- Inspect nearby connectors, fasteners, and mating surfaces before installation.
Installation notes
- Use the listing instructions when present and follow the vehicle service procedure.
- Professional installation may be appropriate when the repair requires special tools or calibration.
Companion parts
- Inspect nearby fasteners, connectors, seals, fluids, and wear items before starting the repair.
- Use the service procedure and the visible package contents to identify any additional parts or tools required.
Before you buy
- Compare the listing title, photos, package contents, and specifications with the part being replaced.
- Confirm vehicle compatibility and installation requirements before ordering.
Customer feedback
Ratings and written reviews
4.3 / 5
34 source ratings
Source: Amazon. Imported marketplace feedback is shown for product research and is not a review of a purchase made on this website.
Customer –
This switch fit perfect in my Jeep TJ and looks custom with the KC HiLites logo. Had a question on install and the seller got back to me right away and it was late on a Sunday! Great customer service and will buy more as I add more lights.
Ernest vasquez –
I installed it in my 2006 TJ and it fits perfect. Looks good. Lights up when activated
Dobie S. Pinscherman –
Needing to add some offroad lights, but not wanting to pay mopar prices, I grabbed a few of these to check them out. They seem a little light, and feel somewhat “cheap”, but I tried them anyways. They snap right into the panel, after you removed the blanks. I grabbed 4, to run lights on all 4 sides. I used Sopoby self soldering connectors (available on amazon) to wire the hot feed and grounds together. I spliced into the cigarette lighter harness, on the keyed side. (One lighter plug is always hot, the other is keyed, on my 2006) the voltage and Amp load needs to light the switch, and signal the relay, not carry the load of the lights or accessories. I grabbed a set of relays with pigtails from amazon to run the lights. After solder-connecting the wiring with the sopoby’s, I powered them up, and tested them.They light up with a little orange led, when you turn them on, and are dark when turned off. Mine all worked without any issues or problems. The switches have a positive detent or “click” when operated. A short run of 14-4 thnn wire to the relays under the hood, and I was done with install. Worth the money, so far, at a quarter the price for mopar switches.
Matt L. –
I’ll Start with saying I LIKE the switches. Clearly, I have four of them. My only complaint is two of them, the indicator light when wired stays on whether switch is on or off (dome and rock) and two light up only when switch is on (lightbar and reverse). Because of such, I have just not used the wire for the indicator as I want that to show on only when switch is on. They were all wired to the same hot so this is a manufacturing inconsistency.The switch physically itself does not feel like a light switch. The motion is kinda springless. But who cares. It does the job.Fit is PERFECT to factory inserts. Just pop the dummy cover off from the back and click these in. That easy! Appear like they came from factory
Customer –
Bought 2 switches. OBoth work but one doesn’t have a good feel for on and off. No real click
Gary Walrath –
Title say it all…
brandon –
The switch matches the OEM ones really well. The included harness is definitely a plus. Fitment was really nice as well
R.D. –
Used this switch along with a wiring harness from Quadratec to wire in a cutoff for the dome / footwell lights in my daughter’s Wrangler. Works flawlessly. Now she can shut these off easily when removing the doors this summer. The fitment and installation is also easy. A little pricey, but nice.