Description
Review this item in the context of the repair, installation access, nearby parts, and the result the completed job is intended to achieve.
No structured vehicle fitment data is available. Compare the listing with the vehicle and existing part before ordering.
Repair scenarios, installation, companion parts, and use outcomes
Buying guidance
Quick decision
Review this bearing pullers in the context of the repair and the surrounding components.
Repair scenario
- Identify the symptom and confirm that this is the component required by the repair.
- Inspect nearby connectors, fasteners, and mating surfaces before installation.
Installation notes
- Use the listing instructions when present and follow the vehicle service procedure.
- Professional installation may be appropriate when the repair requires special tools or calibration.
Companion parts
- Inspect nearby fasteners, connectors, seals, fluids, and wear items before starting the repair.
- Use the service procedure and the visible package contents to identify any additional parts or tools required.
Before you buy
- Compare the listing title, photos, package contents, and specifications with the part being replaced.
- Confirm vehicle compatibility and installation requirements before ordering.
Customer feedback
Ratings and written reviews
4.7 / 5
24 source ratings
Source: Amazon. Imported marketplace feedback is shown for product research and is not a review of a purchase made on this website.
Steve –
Handy tool for my RC tool bag.
Tanner –
The only issue I had was the punches will want to bend if you are not careful. Take your time and line everything up, it will take more than one try. Once everything is lined up correctly it should come apart smoothly
Szechuan Chicken –
If your savvy, and very patient, you can actually use this on other motor size pinion removal as well. I was easily able to use this on a 330 size, but it is intended for a 180. Key here is patience.Well made pinion remover. Threads are smooth, just add a tab of oil to help, and then use the included adapter as needed and gently work the pinion off.No instructions are included, but check popular forums and videos for information on “how to”. Plenty videos exist for 550 size motors and just use those and adapt.Set includes adapter, installer, device, and 3 different sizes (1.3, 1.8, 2.8) for pinon removal.
Madeline Barrientos –
This puller is too narrow to use easily with 550 size motors, especially ones with long shafts (lookin at you, cheap kids’ ride-on toys). However, pressing being more an art than a science, I made do with a couple of nickels as shims. Also note that I had to back out the shaft insert a few threads and use the lower slot in the arms, which is normally used for pinion installation, to instead pull the 550 motor’s pinion. Perhaps I should have paid more attention to the detailed dimensional diagrams in the item photos before purchasing this puller. Other than that, no real complaints.I had to use a c-clamp to install the pinion since the 550 motor won’t fit inside this pinion tool.Go ahead and oil all the threads before using this. It makes pressing so much easier. Make sure the shafts stay aligned, they tend to walk under load and rotation. Also push the motor shaft as far as you can into the v-slot on the plate, this keeps the plate from bending under load. Be patient, this device will work with you if you work with it.
Ohannon7 –
This one works, while the small brass ones crack. I know this bc I bought a brass pinion puller but it was made too thin and snapped. This MEUS puller is strong like bull! 🐂
Serena Ann –
This is a handy tool for installing and removing rc pinions. Thry can be pretty tricky to do by hand so this definitely makes the job a breeze. Very cool uniwue good quality tool.
bruteforce –
I used this to remove and press on a new pinion gear on my Mofo Nanabeast motor. I found it super easy to use and had the job completed in less than 5 minutes from the time I opened the box. Now I can play around with brushless motor gearing options with pressed on pinion gears.
albert ruiz –
It works only on motors that actually fit between the two sides if its any bigger than its useless KP000