Description
Review this item in the context of the repair, installation access, nearby parts, and the result the completed job is intended to achieve.
Product Description
AUXMART 10″ Universal 4 Way Guide Wire Winches Roller Fairlead Designed for Exclusive Use with Wire Winch Rope, Avoids Binding and Tackles Angled Pulls with Ease.
-
What is the largest diameter cable that will fit through?
The largest diameter of atv winch rope or cable will fit.
-
What is the exact size of rectangular hole through which cable passes?
The hole is at least 3 1/2″ wide X 3/4″ high, can be used with Rope or Cable.
-
Does it come with mounting hardware?
No, it does not come with mounting hardware.
PRECISION MACHINED
Rollers are treated with zinc galvanization and chromed to provide superior protection from the elements, significantly less likely to chip and rust
RUGGED CONSTRUCTION
Solid construction and rollers move freely to reduce friction and protect your winch cable from wear, helping extend the service life of the cable
HIGH STRENGTH
Constructed from ultra-high tensile strength steel, high strength, wear-resistant, and corrosion resistant, extended life in harsh environments
4-WAY ROLLER DESIGN
Dowel-pin bearings and composite bushings on multi-directional rollers provide for smooth operation even during extreme angle pulls
Premium ATV roller fairlead
CAPACITY
- Designed for use with winches with capacities from 8,000lbs – 17,500lbs
- Work with most popular winches and winch mounts using a 10″ wide bolt pattern, and 2.5-3.5″ diameter drums
UNIVERSAL APPLICATIOIN
- Bolt Pattern: 10” Standard Mount Pattern
- Dimension: 11.5”（L）x 4.4”(W) x 3.5”(H)
- Universal roller fairlead that will work with all brands of winches and and ATV brackets.
Average Guy –
There has been a lot of talk about the plastic bushings in the rollers. I attached this to and ARB winch bumper on a 1993 Jeep Cherokee XJ. The winch has a single line pull capacity of 9,200 lbs. We use the XJ for fishing and general off roading and exploration. So far, the only pull straight ahead with the winch was when it was installed. Our first pull on the trail was immediately to the left of the vehicle, and with the XJ stuck in a channel, the left and upper roller had a lot of pressure on them. Enough pressure for the winch cable to scratch up the roller, but the roller nor its bushings failed in any way. The channel prevented the Jeep from being pulled toward the tree the winch was attached to until the cable was nearly 90 degrees to the vehicle and only then did the Jeep pop out of the channel and turn toward the anchor point. We have used the winch many times and the cable is always off to the left or right. To date there is no damage to the rollers. I have not pulled by deadmanning to an anchor point and winching a 10,000 lb vehicle or heavier nor do we do heavy rock crawling.All in all, we are very happy with this fairlead and if it fails under extreme conditions, I would replace it with another one.
eric –
I’ve needed a fair lead for quite a while. The price was right. Installed easily. Ran my winch cable out. Rollers work good
Steve Gould –
The quality looks decent and the fit was perfect. I was replacing a Harbor Freight fairlead that was damaged after sucking the cable in too far.One year review: After a year of use I have only had to winch five or six times. The rollers are a bit soft and show quite a lot wear and burrs from the cable. I have had to pull the pins after each use as the rollers get stuck and don’t turn by hand. I have not tried any lube because that usually turns into glue. Cleaning out the dirt has done the trick so far, but the plastic sleeves are not wearing well. The pins have held up well so far, not bent like the Harbor Freight one did. For the little use mine gets I would say it is worth the price. If you use your winch frequently I would recommend a higher quality alternative.
Larry –
Perfect, perfect. The original fairlead was at least35 years. 1 side roller came up missing The new 1 35 years later same quality, same weight, perfect fit. Thank you nice job
Osamahalawi –
ممتاز وجوده عاليه
Albert amundsen –
Used for mounting to Ramsey winch. Appears to be well made
Vickie McClary –
Quality is good – fits exactly as expected.
Customer –
Good quality
George Hammack –
Fit the bumper nicely with no issues